Find the right bottom outlet valve for your requirements!
Our valve finder will help you find the right bottom outlet valve for your requirements. Searched and not found? Our range goes much further. For special products and individual advice, contact us directly.
Filter the results
Showing 121–126 of 160 results
PFA lined ball valve, Neotecha
Um eine besonders gute mechanische Festigkeit des Kerns und eine hohe chemische Beständigkeit der Auskleidung zu erreichen hat Neotecha eine spezielle Technik entwickelt um PFA auf einen Metallkern aufzutragen. Mit dieser Technik bietet Neotecha Armaturen die weltweit bekannt sind, für ihre Zuverlässigkeit in den schwierigsten korrosiven Anwendungen. Der PFA-ausgekleidete Kugelhahn von Neotecha-Emerson eignet sich aufgrund seiner qualitativ hochwertigen Verarbeitung hervorragend um gute Standzeiten in den härtesten Prozessumgebungen zu erreichen. Zuverlässigkeit in den anspruchsvollsten korrosiven Anwendungen!
Pinch valve aiRFlex®
“The aiRFlex® pinch valve is designed for abrasive, corrosive and scaling sludge, liquids and powders.
It is characterised by a full bore and it is interchangeable with most ball valves and diaphragm valves.
Technical advantages:
* Patented expansion folds prevent stretching. This reduces the stress on the tube and significantly increases the service
life
* No moving parts – tube is the only wear part.
* Trouble-free operation – no blocking or clogging.
* Increased service life of the tube, which does not stretch when closed.
* Cost-effective solutions as no actuator is required.
* The tube can be replaced without having to remove the valve from the line, thus guaranteeing low maintenance and operating costs.
Operating pressure about 2 bar below
the available factory air supply, up to
max. 6 bar.
The MONSYS monitoring system prevents
unexpected emergency repairs.
“
Pinch valve RF VALVE
“The pinch valve RF is designed for abrasive, corrosive and scaling sludge, solids, liquids and powders.
It is characterised by a full bore and it is interchangeable with most ball valves and diaphragm valves.
The MONSYS monitoring system prevents unexpected emergency repairs.
Technical advantages:
* Patented expansion folds prevent stretching, thus reducing the stress on the tube and significantly increasing the service life.
* No moving parts so the tube is the only wear part.
* Trouble-free operation: no blocking or clogging.
* Increased service life of the tube, which does not stretch when closed.
* Cost-effective solutions as no actuator is required.
Available in nominal diameters from DN25 – DN 1500
The tube can be replaced without having to remove the valve from the line, thus resulting in low maintenance and operating costs.
Actuator types: pneumatic, electric and hydraulic”
* Kostengünstige Lösung, da kein Antrieb benötigt wird.
Erhältlich in den Nennweiten DN25 – DN 1500
Der Schlauch kann gewechselt werden, ohne daß die Armatur aus der Leitung herausgenommen werden muss, was in niedrigen Wartungs- und Betriebskosten resultiert.
Antriebsarten: pneumatisch, elektrisch und hydraulisch”
Piston check and piston closing check valve, forged, metal seated
Wakmet piston check valves made of forged steel prevent the backflow of medium into the pipe. The check valve can also be used as a shut-off valve to open and stop the flow.
Depending on the model, the temperature ranges extend up to 530°C or 670°C (up to ≤ 200°C for PTFE).
Wakmet metal seated piston check valves are mainly used in the energy sector as well as in the pulp and paper industry. Depending on the type, they are suitable for media such as water, steam, non-aggressive and non-toxic media as well as some also for gas, fuel and sea water.
Plastic ball valve
The plastic CEPEX ball valves can be used both to shut off and control liquids.
The ball valves made entirely of plastic bring advantages in terms of resistance to chemicals. The EXTREME series is designed for special requirements and can therefore be used in steel plants, chemical plants or the oil industry.
The plastic ball valves can be operated either manually or also automatically. The model is available in a wide variety of plastics (PVC-U, CPVC, PP-H, PVDF and ABS).
Plastic butterfly valve
The CEPEX plastic butterfly valves can be used to shut off and control liquids.
The valves made entirely of plastic have the advantage that they are resistant to chemicals. The EXTREME series is designed for special requirements and can therefore be used in steel plants, chemical plants or the oil industry.
The plastic butterfly valve can be operated either manually or also automatically and is available in a wide variety of plastics (PVC-U, CPVC, PP-H, PVDF and ABS).